tenon

Weak Neck Fail

repair guitar neck

This is a particularly handsome Heritage 535. It would be even more handsome if it were in one piece instead of two, though. The neck's come off and a little bit of investigation shows that it never stood a chance. This neck joint was weak from the start.

These joints are referred to as 'mortice and tenon' joints. In this case, the tenon (the bit at the end of the neck) was too small for the mortice (the 'pocket' in the body). As well as having a relatively large shim on one side, the tenon didn't make contact with the bottom of the pocket. There's an gap of a couple of millimetres between the two.

You can see the circled bits in the image. On the left is a chunk of mahogany from the tenon that's split off and the glue line is visible on the right. You can see the gap.

That gap means no glue joint there. Only the sides are glued (well, those and the 'face' of the joint but that's not providing a lot of strength).

This is a weak neck joint that was much more prone to fail that it ought to have been.

Rather than just gluing it back together, I'm going to build up the tenon to get this joint to where it should have been from the factory.

guitar neck tenon break
neck joint failure repair

First off, that little chunk of mahogany that's still glued to the side of the neck pocket has to be removed and glued back to the neck tenon. Once that's done, I nab a new bit of mahogany and thickness it so that it will fill the gap.

In the right photo, you can see I've glued this on and cut it to match the shape of the existing tenon. The thickness of the added wood gives you an indication of how much of a gap there was.

fix guitar neck joint
repair guitar tenon joint

I removed the old glue from both parts and re-glued the neck to the body. Because the break was quite clean, only a little touch-up work was required to get the guitar looking its best.

This repair looks good and, importantly, has actually resulted in a better, more sound, neck joint than when it left the factory.

Les Paul Neck Removal and Repair

les paul broken neck heel

Yikes. If you've been reading my stuff for a while, you've probably spotted a few different examples of neck breaks. Most of these have been up at the headstock end as that's the more likely place for a break.

It can happen down the other end too, though. This Les Paul took a tumble and broke in a nasty way. The exterior damage is obvious but it's pretty certain that crack extends into the neck tenon too (the tenon's the bit that gets glued into the neck pocket in the body).

This neck needs to come out to be properly repaired.

It's not too often that I need to remove a Les Paul neck, which is lucky as it's a relatively involved job. With a strong cup of tea to steel myself, I set to work.

les paul heel repair frets
les paul neck removal

First up, a few frets need to come out. To remove this neck, I need to soak and steam the glue out and that means getting access to the internals of the neck joint. I do this by drilling small 'access' holes. These are drilled in the fret slots. When it's all done, I'll fill the holes with rosewood plugs and re-cut the slots. All of this is hidden by the refitted frets.

Your eagle-eyes will have noticed a little dot on each (numbered) fret. These frets will be refitted and the dot tells me which is the bass end.

Keeping fingers crossed, I take a look under the neck pickup, hoping for a long tenon. No luck. If I could have seen the end of the tenon, I'd know exactly what size it was so I could position my holes to accurately access the sides of the neck joint  (if it's not clear what I mean here, a photo later on might clarify things).

Since all of this tenon is hidden, I have to measure out the usual Gibson size and position for this guitar and hope that it's built properly to spec.

In the photo, above on the right, you can see the pencil marks I've used to plot out the tenon and the holes I've drilled to get access to the joint.

gibson neck removal
steaming off gibson neck

This one's a bit weird-looking, I'll admit.

In the left image, I'm using a syringe to insert boiling water into the holes I've drilled. I give it a few seconds and then suck it back up again. What comes out is cooler water with some manky-looking dissolved glue. I repeat this process a lot over the course of a couple of days. A Les Paul neck joint is a hell of a strong joint and doing this gives me a little bit of a head start before I hit it with the steam.

Which is what's happening on the right. That nozzle lets me get piping hot steam deep into the joint. The heat and moisture helps to dissolve more glue and, after some time and work, the glue eventually lets go…

les paul neck tenon
les paul neck joint repair

…Leaving most of the bloody tenon still in the pocket. D'oh!

The heel crack extended into the tenon as we thought. Now I have to keep working to get this piece out with pretty much no leverage.

More tea required, I think.

Some steamy swearing later and it's out. Now, in the side of that neck tenon, you can see the tracks of those holes I drilled earlier. We were right on the money with the positions too—nice.

gibson guitar neck tenon repair
les paul neck joint fix

And here's the jigsaw we need to get back together. You'll notice a small shim in the neck pocket. This was installed at the factory (it's not uncommon) and I'll reuse it for this repair.

All of the old glue is cleaned from the mortice and the tenon and then, the two bits of neck are glued back together. Again, the tracks of those access holes are clear in the photo on the right.

gibson neck tenon repair
les paul repair touch-up

Once it's sound again, the neck is reattached to the body. Those frets are reinstalled and all the frets are levelled to ensure clean playability.

Then, it's just some touch-up to hide the evidence. As the rear and neck of this Les Paul are black, the opaque colour easily disguises the repair.

It took a bit of thought, a lot of work and twelve buckets of tea but this job's a good 'un.