broken

Headstock Repairs - Reinforcement

Broken Gibson headstock repair

We've talked a lot about neck resets over the last few weeks so let's move down the other end of the neck. Headstock breaks.  

Nobody likes to see it happen but sometimes your guitar takes a tumble and the impact can—all too easily—snap the headstock. In most cases, this is a (reasonably) straightforward repair and can be re-glued soundly.  

Sometimes, though, the nature of the damage can force us down a more 'involved' path. If the break is 'short' (i.e. it doesn't provide a lot of glueing area to ensure a sound repair) it may be necessary to consider some reinforcement to ensure the repair holds.  

One solution is what's called a 'backstrap overlay'.  

This involves overlaying some fresh wood over the repaired break. The new wood glues onto the unbroken wood either side of the crack to add strength.  

Let's take a look at one. 

Reglue headstock before applying backstrap

Remove wood to accept overlay

In the first photo directly above, I'm repairing the break. This might seem odd but I need to get everything back together properly before I apply any reinforcement. The repair is carried out as it would normally be since the actual re-gluing isn't the real problem—the problem is keeping it in one piece after string-tension is applied. I need to glue-up everything as normal and then reinforce things to ensure the repair is strong.

When the initial repair is done and the glue has dried, I can begin the real work on this one. I remove a few millimetres of wood from the rear of the headstock and, past the break, along the neck. It would make for a more discreet repair if I brought this all the way to the end of the headstock but, on a Gibson, I like to stop short of the serial number. If the guitar is ever sold on, a perspective buyer may be put off more by the lack of a serial number than a well-executed repair. 

The photo above on the right shows the removed section. I'll inlay the new wood here so let's get on with that.

Clamping for backstrap overlay on Gibson neck break

New wood overlaid over broken neck

The wood to be overlaid on the headstock is thicknessed and cut to the rough dimensions. To accommodate the angle between headstock and neck, I bend the new wood. It's this bending that adds extra strength to this repair as the wood grain curves to the correct angle.  

Repairing guitars often makes for some intricate clamping setups and overlays are prime culprits. A shaped caul is useful to get the wood in that curved bit glued in properly. The roughly shaped wood overlay is pretty obvious (and pretty ugly at this stage) in the photo on the right. 

Newly inlaid wood cut to shape on headstock

Tuner mounting holes drilled in overlay

This is where things take shape (pun intended). The overlay is cut to shape and the tuner holes drilled.  

At this point I can go through the usual finish prep. Grain-filling, sanding, etc. In cases like this I need to match the colour of the original finish on the newly overlaid wood. I also have to manage the transitions between new and old finish carefully to keep things looking as inconspicuous as possible. Sealer, colour, and a number of clear-coats later and I'm ready for the next step. 

Waiting.  

Have to wait for the finish to cure properly. Then sanding and buffing and polishing and reassembling and stringing-up and… 

Playing. 

All is well with the world.  

Gibson headstock break repaired with backstrap overlay

Les Paul neck repair with reinforcement

Les Paul Neck Removal and Repair

les paul broken neck heel

Yikes. If you've been reading my stuff for a while, you've probably spotted a few different examples of neck breaks. Most of these have been up at the headstock end as that's the more likely place for a break.

It can happen down the other end too, though. This Les Paul took a tumble and broke in a nasty way. The exterior damage is obvious but it's pretty certain that crack extends into the neck tenon too (the tenon's the bit that gets glued into the neck pocket in the body).

This neck needs to come out to be properly repaired.

It's not too often that I need to remove a Les Paul neck, which is lucky as it's a relatively involved job. With a strong cup of tea to steel myself, I set to work.

les paul heel repair frets
les paul neck removal

First up, a few frets need to come out. To remove this neck, I need to soak and steam the glue out and that means getting access to the internals of the neck joint. I do this by drilling small 'access' holes. These are drilled in the fret slots. When it's all done, I'll fill the holes with rosewood plugs and re-cut the slots. All of this is hidden by the refitted frets.

Your eagle-eyes will have noticed a little dot on each (numbered) fret. These frets will be refitted and the dot tells me which is the bass end.

Keeping fingers crossed, I take a look under the neck pickup, hoping for a long tenon. No luck. If I could have seen the end of the tenon, I'd know exactly what size it was so I could position my holes to accurately access the sides of the neck joint  (if it's not clear what I mean here, a photo later on might clarify things).

Since all of this tenon is hidden, I have to measure out the usual Gibson size and position for this guitar and hope that it's built properly to spec.

In the photo, above on the right, you can see the pencil marks I've used to plot out the tenon and the holes I've drilled to get access to the joint.

gibson neck removal
steaming off gibson neck

This one's a bit weird-looking, I'll admit.

In the left image, I'm using a syringe to insert boiling water into the holes I've drilled. I give it a few seconds and then suck it back up again. What comes out is cooler water with some manky-looking dissolved glue. I repeat this process a lot over the course of a couple of days. A Les Paul neck joint is a hell of a strong joint and doing this gives me a little bit of a head start before I hit it with the steam.

Which is what's happening on the right. That nozzle lets me get piping hot steam deep into the joint. The heat and moisture helps to dissolve more glue and, after some time and work, the glue eventually lets go…

les paul neck tenon
les paul neck joint repair

…Leaving most of the bloody tenon still in the pocket. D'oh!

The heel crack extended into the tenon as we thought. Now I have to keep working to get this piece out with pretty much no leverage.

More tea required, I think.

Some steamy swearing later and it's out. Now, in the side of that neck tenon, you can see the tracks of those holes I drilled earlier. We were right on the money with the positions too—nice.

gibson guitar neck tenon repair
les paul neck joint fix

And here's the jigsaw we need to get back together. You'll notice a small shim in the neck pocket. This was installed at the factory (it's not uncommon) and I'll reuse it for this repair.

All of the old glue is cleaned from the mortice and the tenon and then, the two bits of neck are glued back together. Again, the tracks of those access holes are clear in the photo on the right.

gibson neck tenon repair
les paul repair touch-up

Once it's sound again, the neck is reattached to the body. Those frets are reinstalled and all the frets are levelled to ensure clean playability.

Then, it's just some touch-up to hide the evidence. As the rear and neck of this Les Paul are black, the opaque colour easily disguises the repair.

It took a bit of thought, a lot of work and twelve buckets of tea but this job's a good 'un.